Skip to main content
Skip table of contents

Ed-Fi Beginning of Year Setup

Introduction

Prior to publishing for a new school year, you must enable the school year in the PowerSchool Data Exchange (DEX) configuration. Use one of the following processes to enable the new school year for Ed-Fi publishing:

Ed-Fi Beginning of Year Setup#Enable School Year in Existing Profile - If your state's Endpoint and Authentication URLs have not changed, you can use the same profile as the previous school year.

Ed-Fi Beginning of Year Setup#Enable School Year in New Profile - If your state's Endpoint and Authentication URLs have changed, create a new profile prior to enabling the new school year.

Note: Use these processes if Ed-Fi was previously enabled for your district. If Ed-Fi has not been enabled, refer to Initial Ed-Fi Setup.

Enable School Year in Existing Profile

Configure PowerSchool Data Exchange

  1. On the start page, select the School link at the top of the page and choose District Office.

  2. Under the Setup menu, click System.

  3. Under Data Exchange, click General Setup.

  4. On the Data Exchange Setup page, select the Profile Name.
    Important Note: All Communication Settings, including LEA settings, are profile specific. Verify that you have selected the correct profile before making changes.

    1. Select the School Years for which you are publishing. Refer to your state Release Notes for more information on when the new school year (i.e., 2018-19 checkbox) was added to the options.

  5. Click Save.

Run “Publish Missing” or “Publish All” for each category on the Ed-Fi Dashboard a few days prior to state funding deadlines and at the beginning and end of the school year to verify that all records are updated to the state ODS. Refer to Publish Data for more information. Refer to Enable DEX Plugin for more information on plugins.

Enable School Year in New Profile

Create a New Profile

PowerSchool Data Exchange (DEX) is delivered to PowerSchool as a plugin. If you need to enable the DEX Plugin or if this is your first-time using Ed-Fi, refer to Initial Data Exchange Setup.

To access the Plugin Management Dashboard, sign into PowerSchool at the district level.

  1. On the start page, select the School link at the top of the page and choose District Office.

  2. Under the Setup menu, click System.

  3. Under Server, click System Settings.

  4. Click Plugin Management Configuration.

  5. Verify that the Enable/Disable checkbox for PowerSchool Data Exchange (DEX) is selected.

  6. Click PowerSchool Data Exchange (DEX).

  7. In the PowerSchool Data Exchange (DEX) Setup page, click Profile Configuration.

  8. Click Add Profile.

    1. Enter a Profile Name. This name shows in the Data Exchange menu list in the main menu. PowerSchool recommends keeping the name under 20 characters.

    2. Select the profile name in the Profile Type dropdown.

    3. Select Enabled On, and Save the profile.

When a plugin is updated, PowerSchool may disable the plugin for security reasons to require a review of the changes and again agree to the terms and conditions for using the software. After a release is installed, verify that all applicable plugins are enabled.

Configure PowerSchool Data Exchange

The setup page provides a user interface for entering various configurable settings including enabling and disabling the entire framework, authentication, and operational frequencies. PowerSchool supports multiple LEAs in a single instance. The setup page contains a section where the individual authentication keys and secrets are entered for each LEA through the Configure hyperlink.

  1. On the start page, choose System under Setup in the main menu.

  2. Under Data Exchange, click General Setup.

  3. In the Data Exchange Setup page, select System Enabled to On. Leave the remaining fields at their default values. Refer to General Setup for more information on the configuration options.

  4. Select the Profile Name.

    All Communication Settings, including LEA settings, are profile specific. Verify that you have selected the correct profile before making the following changes.


  5. The Data Exchange URL and Authentication URL will be automatically populated.

  6. Select the School Years for Ed-Fi publishing.

  7. Verify all applicable Service Options are checked.

  8. Click Configure for any LEAs that will be publishing.

    1. Select On to enable the LEA.

    2. Enter the Authentication Key.

    3. Enter the Authentication Secret.

    4. Test the connection and save communication settings.

      1. PowerSchool recommends that you test your connection after completing these communication settings. Click Test Connection. A message appears to inform you whether or not the test was successful. Click the Save button to record your settings once the test is successful.

  9. Click Save to save the Data Exchange Setup.

Next Step

The next step in the setup process is to download state-provided data.


JavaScript errors detected

Please note, these errors can depend on your browser setup.

If this problem persists, please contact our support.